| Customization: | Available |
|---|---|
| After-sales Service: | 1 Year |
| Warranty: | 1 Year |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
Good quality wet wire drawing machine for making carbon steel alloy steel wires
1. DUCK PAY-OFF MACHINE
The duck pay-off is used for continuous paying-off of wire rod, is the first step in a wire drawing line. Its design has the following advantages:
-Low-noise operation
-No damage of wire surface and lubricant carrier
-Easy handling for loading process
-High pay-off speed
-High safety standard against accidents
Main Technical Parameters of Duck Pay-off:
Loading capacity: 2.5T
Wire rod diameter: 6.5/5.5mm
Process material: High carbon steel
Inlet tensile strength: 1150Mpa
Space requirement: 4600mm*1200mm*2100mm
Weight: 992kg
2.MECHANICAL WIRE DESCALING MACHINE 8BK
1. Description
The descaling machine is welded by 16mm thickness steel plate. At the bottom installs rust collection. Two units of descaling wheels are fixed at the plate in vertical. Wheels use alloy material. The wire rod go pass horizontal and vertical wheel unit then rotate 180°, oxide scale fall into the collection trolley.
2. Main parameters
| Sr. | Name | Description and note |
| 1 | Machine name and model | Mechanical wire descaling machine 8BK |
| 2 | Inlet wire diameter | Φ6.5-5.5mm |
| 3 | Inlet wire material | High carbon steel |
| 4 | Descaling wheel material | Alloy steel |
| 5 | Descaling wheel effective diameter | 7*Φ75mm + 1*Φ107mm |
| 6 | Descaling wheel number | 7+1 |
| 7 | Control | Frequency control |
| 8 | Wire speed max | 2.5m/s |
3.SAND BELT MACHINE
| Sr. | Item | Specification |
| 1 | Name | Sand belt machine |
| 2 | Wire range | Φ5.5-6.5mm |
| 3 | Working speed | 2.5 m/s |
| 4 | Belt quantity | 2 |
| 5 | Belt line speed | 8.8m/s |
| 6 | Main motor power | 15KW frequency motor |
| 7 | Belt particle | 80-120 particle |
| 8 | Belt dimension | W280* L1250 |
| 9 | Abrasive belt particle material | Ceramics or Zirconium corundum |
| 10 | Control system | PLC program control and host computer control |
| 11 | Lubrication | Artificial operation, glycerin lipid |
4.ONLINE LARGE WHEEL TYPE PHOSPHATING BOX
Composition:
This equipment is mainly composed of guide roller, box body, large wheel, bracket, motor, thermal oil heater, dryer, etc.
Working mode:
After the descaling and grinding of wire rod surface, it finally enters the device in a dry and clean state. The wire rod is wound on the big wheel according to the work needs. After the wire rod runs for a sufficient period of time, the wire rod will be sent out of the device after the drying device. While the device is working, a thermal oil heater is used to heat the large wheel box by extracorporeal circulation.
Equipment form:
(1) Steel wire immersion online coating;
(2) Single drum traction, active winding;
(3) Single capstan adopts horizontal installation, supported at both ends;
(4) Pneumatically controlled side gear clutch connects the traction drum and the output shaft of the reducer for transmission;
(5) The tank has automatic heating function.
5.LT15/560 Wet type wire drawing machine
Operating range:
(1)High carbon steel wire
(2)Inlet wire diameter: 6.5/5.5mm
(3)Outlet wire diameter: 2.2/1.4mm
(4)Total compression rate: 91.54%
(5)Final wire application: the finish wire meets the requirements to make sleeping Mattress spring wire.
Cone pulley:
(1) Cone pulley adopts the integral type
(2) The material is ZG55 steel.
Cooling:
(1)Steel:Water emulsion immersion
(2)Using large circulating cooling
Transmission form:
Herringbone gear transmission
Technical parameters:
5. Coiler take up machine XB560
Capstan material:
Φ560mm material is ZG45 cast steel, through quenching and tempering treatment after rough lathing. There's no pore and trachoma and other casting defect.
Frame:
The frame uses the sturdy welding component, all the material surface corrosion depth less than 0.3mm. Surface makes the rust treatment, the welding components use normalized treatment to eliminate welding stress, ensure the accuracy and strength of the component.
Transmission:
Main transmission uses the V-belt, and is also equipped with the pneumatic brake, smooth braking.
1. We have gotten ISO9001:2008 standard and certificate
2. Company established year: 1985
3. Company location: Wuxi city, 125km away from Shanghai
4. FOB port: Shanghai
5. Business type: Manufacturer
6. Number of employees: 100-200
7. Welcome to visit us, we will pick you up at Shanghai airport or other place near Wuxi
){kind=link}